Electrolux 40 II 40 CC Chainsaw Kullanım Kılavuzu

Kullanım Kılavuzu için aygıtı Electrolux 40 II 40 CC Chainsaw

Electrolux 40 II 40 CC Chainsaw Kullanım Kılavuzu

İçeriğini ayıklar

No Özeti sayfasında içerik 1

MAC 538E / MAC 539E 38 CCMAC 540E / PROMAC 40 II 40 CCMAC 542E / CALIFORNIA 42 CCMAC 545E / PROMAC 46 II 46 CCP 538E / EUROMAC S42 / S44 38 CCP 540E 40 CCP 542E / EUROMAC S43 42 CCP 461 II / TITANIUM 460 46 CCElectrolux Outdoor ProductsVia Como 7223868 Valmadrera (Lecco)ITALIAPhone + 39 0341 203111 - Fax +39 0341 581671Our policy of continuous improvement means that the specification of products may be altered from time to time without prior notice.Electrolux Outdoor Products manufacture product

No Özeti sayfasında içerik 2

E.H.MAC 540E - MAC 542EMAC 538E - MAC 539E California - MAC 545EP 540E - P 542EP 538E - Euromac S42Euromac S43Euromac S44Titanium 46014”50T350mm3/8”GBPromac 40 IIPromac 46 IIP 461 IIF.I.400mm55T3/8”18”450mm60T3/8”16”400mm66T.325”FRNLNOXFISE(5/32”)16”DEDKXX(5/32”)(5/32”)XX(5/32”)(5/32”)ESPTITGRHUCZXPLTR(3/16”)RU18”450mm72T.325”X(3/16”)G.L.Due to a constant product improvement programme, the factory reserves the right to modify technical detailsmentioned in this m

No Özeti sayfasında içerik 3

A. General description1 - BAR2 - CHAIN3 - FUEL TANK CAP4 - OIL TANK CAP5 - STOP SWITCH6 - STARTER HOUSING7 - STARTER HANDLE8 - FRONT HANDLE9 - AIR FILTER COVER10 - CHOKE KNOB11 - CARBURETOR ADJUSTMENT SCREWS12 - SAFETY CHAIN BRAKE1314151617181920212223- BAR RETAINING NUTS- CHAIN CATCHER- MUFFLER SHIELD- REAR HANDLE- THROTTLE TRIGGER LOCKOUT- THROTTLE TRIGGER- CHAIN BRAKE COVER- CHAIN ADJUSTER SCREW / INTENZ- SPIKE/SPACER- THROTTLE ADVANCE- DECOMPRESSION VALVESafety precautionsIf not used properl

No Özeti sayfasında içerik 4

Choke partially openedDo not cut with the end on the bar,this may cause kickbackChoke closed (cold start)Never use the machine with only onehandStoppingAlways use the machine with bothhandsBrake engaged / disengagedSwitch off the engine by moving thestop switch to the STOP positionbefore carrying out any checksor maintenance.Beware of kickbackOil/petrol mixB. Safety precautions1 All operators should read this manual carefully beforeusing this chainsaw; only use this machine for usagespecifically

No Özeti sayfasında içerik 5

6 Keep by-standers and animals out of the work area; at aminimum distance of 10 m or twice the timber length. Ifnecessary, use warning signs to keep on-lookers at a distance.Carefully survey the working site to note any hazards, eg.roads, paths, electricity cables, dangerous trees etc. Donot use the chainsaw if the device for stopping the chain(safety chainbrake) does not work correctly. Never placehands on the chain whilst the engine is running. Ensuresomeone is within hearing distance in case

No Özeti sayfasında içerik 6

E. Starting and stoppingIMPORTANTNever start or operate unless bar and chain are properlyinstalled. Before starting always move the saw awayfrom the fuelling area and place it on a firm, flat surface,the guide bar to the front.STARTING A COLD ENGINE1 Check that the chain brake is in the disengaged positionmoving the lever (L) towards the front handle.Move the stop switch upwards .2 Slide the choke lever (A) to the CLOSED position (OUT).Push the decompression valve (D) down if your models isfitte

No Özeti sayfasında içerik 7

Then open screw 1 full turn (counterclockwise) .If acceleration is not smooth, open another 1/8 turn toincrease fuel flow .• H: The needle screw H governs fuel flow at high speed(throttle valve fully open).To set hi speed screw H: close screw H turning it clockwise without forcing .Then open screw 1 full turn (counterclockwise) .If the engine speed is too high, open the screw about 1/8turn (counterclockwise). Optimal adjustment is foundbetween 1 and 1 1/4 turns.• I: The I (IDLE) screw contro

No Özeti sayfasında içerik 8

The chain brake should snap into both positions.Ifstrong resistance is felt or lever does not move intoeither position, DO NOT USE YOUR SAW. Take it immediately to an authorized servicing dealer.3 CHAIN CATCHERThis unit is fitted with a chain catcher below the drivespocket. This is intended to stop the rearward movement ofthe chain in case of breakage or if it should come out of thebar. It should never be removed.L. Chain sharpening1 Chain cutter teeth can be sharpened with a round file,as follo

No Özeti sayfasında içerik 9

Fault finding tableEngine will not startCheck STOP switchis in the position I.Control fuel levelmin. 25% tank capacity.Engine runs badlyEngine runs badly orlooses power when cutting•Check air filter is clean.••••Remove spark plug,dry it, clean it and adjust it,and replace it, if necessary.••Control and adjustthe carburetor screws if necessary.The chainsaw runsbut does not cut well••Change fuel filter.Contact your dealer.•Carefully follow the chainassembly instructions.•Chec

BİR YORUM BIRAK