Harbor Freight Tools 47269 Heat Gun Kullanım Kılavuzu

Kullanım Kılavuzu için aygıtı Harbor Freight Tools 47269 Heat Gun

Harbor Freight Tools 47269 Heat Gun Kullanım Kılavuzu

İçeriğini ayıklar

No Özeti sayfasında içerik 1

HEAT GUNWITH ACCESSORIES47269ASSEMBLY & OPERATING INSTRUCTIONS®3491 Mission Oaks Blvd., Camarillo, CA 93011Visit our Web site at http://www.harborfreight.comTO PREVENT SERIOUS INJURY,READ AND UNDERSTAND ALL WARNINGSAND INSTRUCTIONS BEFORE USE.Copyright© 2002, 2004 by Harbor Freight Tools® . All rights reserved. Noportion of this manual or any artwork contained herein may be reproduced inany shape or form without the express written consent of Harbor Freight Tools.For technical questions and r

No Özeti sayfasında içerik 2

THANK YOU for choosing a HARBOR FREIGHT TOOLS product. For future reference, please complete theowner’s record below:Model___________Serial No._____________Purchase Date_____________Save This ManualYou will need the manual for the safety warnings and precautions, assembly instructions, operating andmaintenance procedures, parts list and diagram. Keep your invoice with this manual. Write the invoice numberon the inside of the front cover. Keep the manual and invoice in a safe and dry place for

No Özeti sayfasında içerik 3

electrician if you are in doubt as to whether the outlet is properly grounded. If thetools should electrically malfunction or break down, grounding provides a low resistancepath to carry electricity away from the user.5.Double insulated tools are equipped with a polarized plug (one blade is widerthan the other). This plug will fit in a polarized outlet only one way. If the plugdoes not fit fully in the outlet, reverse the plug. If it still does not fit, contact aqualified electrician to install

No Özeti sayfasında içerik 4

TOOL USE AND CARE16.Use clamps (not included) or other practical ways to secure and support theworkpiece to a stable platform. Holding the work by hand or against your body isunstable and may lead to loss of control.17.Do not force the tool. Use the correct tool for your application. The correct tool willdo the job better and safer at the rate for which it is designed.18.Do not use the power tool if the Power Switch does not turn it on or off. Any toolthat cannot be controlled with the Power Swi

No Özeti sayfasında içerik 5

Heat Gun Specific Safety RulesImportant Safety InstructionsRead These InstructionsWARNING: Extreme care should be taken when stripping paint. The peelings, residue and vapors of paint maycontain lead, which is poisonous. Any pre-1977 paint may contain lead and paint applied to homes prior to 1950 islikely to contain lead. Once deposited on surfaces, hand to mouth contact can result in the ingestion of lead.Exposure to even low levels of lead can cause irreversible brain and nervous system damage

No Özeti sayfasında içerik 6

Nozzle is extremely hot. When using the Heat Gun, never allow any body part to contactnozzle. Never touch any hot surface when the Heat Gun is running. Be careful to put the hot Heat Gundown only on a non-flammable surface.Never use heat Gun as a blow dryer. Never direct heat flow to any person or animal.Do not obstruct the airflow. Do not cover air outlet at any time. Do not put anything down on thenozzle.Additional Warnings and Safety InstructionsHidden areas such as behind walls, ceilings, fl

No Özeti sayfasında içerik 7

FIGURE BFIGURE ADOUBLE INSULATED TOOLS: TOOLS WITH TWO PRONG PLUGS4.Tools marked “Double Insulated” do not require grounding. They have a special doubleinsulation system which satisfies OSHA requirements and complies with the applicablestandards of Underwriters Laboratories, Inc., the Canadian Standard Association, andthe National Electrical Code. (See Figure B.)5.Double insulated tools may be used in either of the 120 volt outlets shown in the followingillustration. (See Figure B.)SYMBOLOGY

No Özeti sayfasında içerik 8

EXTENSION CORDS1.Grounded tools require a three wire extension cord.2.As the distance from the supply outlet increases, you must use a heavier gaugeextension cord. Using extension cords with inadequately sized wire causes a seriousdrop in voltage, resulting in loss of power and possible tool damage. (See Figure C.)3.The smaller the gauge number of the wire, the greater the capacity of the cord. Forexample, a 14 gauge cord can carry a higher current than a 16 gauge cord.(See Figure C.)4.If using

No Özeti sayfasında içerik 9

The Heat Gun and included accessories are designed to be used to remove paint from painted surfaces.Never use the Heat Gun with chemical strippers.Other Uses for the Heat Gun1)Shrink plastic wire nuts and other wire jointers for tight fits.2)Remove self-adhesive trim and stickers.3)Wax and remove wax from surfboards, skis, and snowboards.4)Use with PVC shrink wrap sheeting for extra bonding power.5)Thaw frozen pipes and locks. Do not use on plastic pipe!6)Dry out damaged timber or use to highlig

No Özeti sayfasında içerik 10

Step 2)Select the desired and appropriate attachment for the Heat Gun. Slide the attachment onto theNose Cone (32) -see Figure D, previous page.Step 3)Turn on the Heat Gun. The Heat Gun has a High setting, a Low setting and an OFF Setting.Push the Switch (2) in at “H” (top of Switch) for the High setting or at “L” (bottom of Switch) torun on the low setting. Allow it to reach full power and full heat.Step 4)Hold the Nose Cone (32) with attachment 3" to 4" from the surface and/or material

No Özeti sayfasında içerik 11

UnpackingWhen unpacking your Heat Gun in Blowmold Case, check to make sure the following parts are included.If any parts are missing or broken, please call HARBOR FREIGHT TOOLS at 1-800-444-3353.Parts List1234567891011121314151617181920 *21222324Left HousingSwitchShock Proof PadDiodeMotorTapping ScrewScrewFanTapping ScrewVent VRIRegulatorCapacitorCircuit BoardWire ConductorTapping ScrewWire Strain PlateRight HousingRingSheathPower CordTapping ScrewFix SleeveCeramic TubeCover112412213112112111115

No Özeti sayfasında içerik 12

PLEASE READ THE FOLLOWING CAREFULLYTHE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THISMANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANYREPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TOMAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OFTHE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALLREPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CE

BİR YORUM BIRAK